Los bloques de medición son valores que se están midiendo en vivo mediante una herramienta de diagnóstico para determinar la condición en la que están operando los sensores y actuadores del vehículo, así como parámetros de medición que a la hora de hacer diagnosis nos van a servir para comprarla con Boletines técnicos, cartas de diagnósticos o parámetros generales tal y como se ve en el siguiente lista
LISTA DE RANGOS DE OPERACIÓN DE SENSORES
Los grupos o datos de medición están agrupados de la siguiente manera para identificar rápidamente el conjunto de sensores que trabajan en esa categoría
000 – 009 Datos principales motor
020 – 029 Control del picado
030 – 049 Control de la mezcla, captador O2 y catalizador.
050 – 059 Control régimen motriz
060 – 069 Control de la mariposa
070 – 079 Control gas de escape (EVAP, SEC, AIRE, EGR)
080 – 085 Definición calculador
090 – 098 Control árbol a levas y colector de admisión.
099 – 100 Grupos intercambiables
101 – 109 Inyección combustible
110 – 119 Control de carga motriz y presión de sobrealimentación
120 – 129 Comunicación calculadores
130 – 137 Enfriamiento motor
140 – 147 BDE
160 – 169 Control lambda pour SULEV-ULEV
Comenzamos por el grupo más básico, y después en el mismo orden que como marca el párrafo anterior se irán acomodando los grupos en una tabla anexa
BANCO | GRUPO | DESCRIPCION | BANCO | GRUPO | DESCRIPCION |
---|---|---|---|---|---|
Banco 1 | 001 | Engine coolant temperature | Banco 2 | 001 | Engine coolant temperature |
Banco 1 | 002 | Load | Banco 2 | 002 | Load |
Banco 1 | 003 | RPM | Banco 2 | 003 | RPM |
Banco 1 | 004 | Voltaje | Banco 2 | 004 | Throttle valve angle |
Banco 1 | 005 | Throttle valve potentiometer | Banco 2 | 005 | Idle Air Control Valve |
Banco 1 | 006 | Idle Air Control Valve | Banco 2 | 006 | Idle Air Control Valve learning value |
Banco 1 | 007 | Idle Air Control Valve learning value | Banco 2 | 007 | Lambda control Bank 1 |
Banco 1 | 008 | Lambda control | Banco 2 | 008 | Lambda control Bank 2 |
Banco 1 | 009 | Lambda control learning value idle | Banco 2 | 009 | Lambda adaptation (add) Bank 1 |
Banco 1 | 010 | Lambda control learning value partial load | Banco 2 | 010 | Lambda adaptation (add) Bank 2 |
En el siguiente enlace te dejamos un vídeo de para que te pueden servir los datos en vivo utilizando los grupos/ canales y parámetros
GRUPO | DESCRIPCIÓN | MEDICIÓN C/UNIDAD | MEDICIÓN C/UNIDAD | MEDICIÓN C/UNIDAD | MEDICIÓN C/UNIDAD | |||
---|---|---|---|---|---|---|---|---|
010 | Ignition | RPM 1/min | Load % | Throttle valve angle (Potentiometer) % | Ignition Angle (Actual) °KW | |||
011 | Ignition | RPM 1/min | Coolant Temperature °C | Intake air temperature °C | Ignition Angle (Actual) °KW | |||
012 | Distributor Adjustment | RPM 1/min | Load % | No. of crankshaft tooth at camshaft flank low->high XX | No. of cranckshaft tooth at camshaft flank low/high XX | |||
013 | ||||||||
014 | Misfire recognition | RPM 1/min | Last % | Misfire counter N | Misfire recognitrion Activated/ Locked | |||
015 | Misfire recognition | Counter Cyl 1 N | Counter Cyl 2 N | Counter Cyl. 3 N | Misfire recognitrion Activated/ Locked | |||
016 | Misfire recognition | Counter Cyl.. 4 N | Counter Cyl.. 5 N | Counter Cyl.. 6 N | Misfire recognitrion Activated/ Locked | |||
017 | Misfire recognition | Counter Cyl.. 7 N | Counter Cyl.. 8 N | Counter Cyl.. 9 N | Misfire recognitrion Activated/ Locked | |||
018 | Load/RPM Window misfire recognition | Lower RPM limit N | Upper RPM limit N | Lower RPM limit % | Upper RPM limit % | |||
019 | Misfire recognition | Counter Cyl. 10 N | Counter Cyl. 11 N | Counter Cyl. 12 N | Misfire recognitrion Activated/ Locked | |||
020 | Knock Control | Ignition angle retard Cyl. 1 °KW | Ignition angle retard Cyl. 2 °KW | Ignition angle retard Cyl. 3 °KW | Ignition angle retard Cyl.4 °KW | |||
021 | Knock Control | Ignition angle retard Cyl. 5 °KW | Ignition angle retard Cyl. 6 °KW | Ignition angle retard Cyl. 7 °KW | Ignition angle retard Cyl.8 °KW | |||
022 | Knock Control | RPM 1/min | Load % | Ignition angle retard Cyl. 1 °KW | Ignition angle retard Cyl. 2 °KW | |||
023 | Knock Control | RPM 1/min | Last % | Ignition angle retard Cyl. 3 °KW | Ignition angle retard Cyl. 4 °KW | |||
024 | Knock Control | RPM 1/min | Last % | Ignition angle retard Cyl. 5 °KW | Ignition angle retard Cyl. 6 °KW | |||
025 | Knock Control | RPM 1/min | Last % | Ignition angle retard Cyl. 7 °KW | Ignition angle retard Cyl. 8 °KW | |||
026 | Knock Control, KS Voltage | Cyl.. 1 V | Cyl.. 2 V | Cyl.. 3 V | Cyl.. 5 V | |||
027 | Knock Control, KS Voltage | Cyl.. 5 V | Cyl.. 6 V | Cyl.. 7 V | Cyl.. 8 V | |||
028 | Test Knock sensor, short trip | RPM 1/min | Load % | Coolant Temperature °C | Result Test ON /Test OFF/ Sys. OK / Sys. not OK | |||
029 | ||||||||
030 | Oxygen Sensor Status Bank 2 | Bank 1, sensor 1 | Bank 1, sensor 2 | Bank 2, sensor 1 | Bank 2, sensor 2 | |||
030 | Oxygen Sensor Status Bank 1 | Bank 1, sensor 1 | Bank 1, sensor 2 | |||||
031 | Oxygen Sensor Voltage Bank 2 | Bank 1, sensor 1 V | Bank 1, sensor 2 V | Bank 2, sensor 1 V | Bank 2, sensor 2 V | |||
031 | Oxygen Sensor Voltage Bank 1 | Bank 1, sensor 1 V | Bank 1, sensor 2 V | |||||
031 | Linear Oxygen Sensor Bank 2 | Lambda actual value Bank 1 | Lambda Specified Value Bank 1 | Lambda actual value Bank 2 | Lambda actual value Bank 2 | |||
031 | Linear Oxygen Sensor Bank 1 | Lambda actual value Bank 1 | Lambda Specified Value Bank 1 | |||||
032 | Oxygen sensor learning values (Valor Máximo) Bank 2 | Bank 1, sensor 1, idle % | Bank 1, sensor 1, partial load % | Bank 2, sensor 1, idle % | Bank 2, sensor 1, partial load % | |||
032 | Oxygen sensor learning values (Valor Máximo) Bank 1 | Bank 1, sensor 1, idle % | Bank 1, sensor 1, partial load % | |||||
033 | Lambda Control Value Bank 2 | Bank 1, control value % | Bank 1, Oxygen sensor voltage V | Bank 2, control value % | Bank 2, knock sensor voltage V | |||
033 | Lambda Control Value Bank 1 | Bank 1, control value % | Bank 1, Oxygen sensor voltage V | |||||
033 | Linear Oxygen sensor Value Bank 2 | Bank 1, control value % | Bank 1, sensor voltage before cat. converter of a broad band sensorc V | Bank 2, control value % | Bank 2, sensor voltage before cat. converter of a broad band sensor V | |||
034 | Oxygen Sensor aging test Bank 1 or Bank 3 Before Catalytic Converter Short trip | RPM 1/min | Exhaust gas / cat. converter temperature °C | Length of period S | Result Test ON/Test OFF/ B1-S1 OK/B1-S1 not OK Or B3-S1 OK /B3-S1 not OK | |||
034 | Oxygen Sensor aging test Bank 1 or Bank 3 Before Catalytic Converter for linear oxygen sensor Short trip | RPM 1/min | Dynamic factor | Length of period S | Result Test ON/Test OFF/ B1-S1 OK/B1-S1 not OK Or B3-S1 OK /B3-S1 not OK | |||
035 | Oxygen Sensor aging test Bank 2 or Bank 4 Before Catalytic Converter Short trip | RPM 1/min | Exhaust gas / cat. converter temperature °C | Length of period S | Result Test ON/Test OFF/ B2-S1 OK/B1-S1 not OK Or B4-S1 OK /B4-S1 not OK | |||
035 | Oxygen Sensor aging test Bank 2 or Bank 4 Before Catalytic Converter for linear oxygen sensor Short trip | RPM 1/min | Dynamic factor | Length of period S | Result Test ON/Test OFF/ B2-S1 OK/B1-S1 not OK Or B4-S1 OK /B4-S1 not OK | |||
036 | Oxygen sensor readiness after catalytic converter , short trip Bank 2 | Bank 1, sensor 2 | Result Test ON/Test OFF/ B1-S2 OK/B1-S2 not OK or B3-S2 OK/B3-S2 not OK | Bank 2, sensor 2 | Result Test ON/Test OFF/ B2-S2 OK/B2-S2 not OK or B4-S2 OK/B4-S2 not OK | |||
036 | Oxygen sensor readiness after catalytic converter , short trip Bank 1 | Bank 1, sensor 2 | Result Test ON/Test OFF/ B1-S2 OK./B1-S2 not OK. | |||||
037 | Oxygen sensors short trip | Last % | Bank 1: Oxygen sensor voltage after cat. Converter V | Bank 1: TV shift ms | Result Test ON/Test OFF/ Sys. OK/Sys. not OK | |||
037 | Linear Oxygen sensors short trip | Last % | Bank 1: Oxygen sensor voltage after cat. Converter V | Bank 1: D Lambda | Result Test ON/Test OFF/ Sys. OK/Sys. not OK | |||
038 | Oxygen sensors short trip Bank 2 | Last % | Bank 2: Oxygen sensor voltage after cat. Converter V | Bank 1: TV shift ms | Result Test ON/Test OFF/ Sys. OK/Sys. not OK | |||
038 | Linear Oxygen sensors short trip Bank 2 | Last % | Bank 2: Oxygen sensor voltage after cat. Converter V | Bank 1: D Lambda | Result Test ON/Test OFF/ Sys. OK/Sys. not OK | |||
039 | Sensor exchange after Catalytic Converter, short trip | Air mass g/s | Bank 1: sensor voltage V | Bank 2 sensor voltage V | Result Text:Test ON/Test OFF/ Sys OK/Sys. not OK | |||
040 | Oxygen Sensor heaters resistor combined wires and heaters Bank 2 | Heater resistor Banks 1+2, sensor 1 Ω | Condition Heater before cat. ON/ Heater before cat. OFF | Heater resistors Banks 1+2, sensor 2 [Ω | Condition Heater before cat. ON/ Heater before cat. OFF | |||
041 | Oxygen Sensor heater Bank 1 | Resistor Bank 1, sensor 1 Ω | Condition or duty cycle Heater before cat. ON/ Heater before cat. OFF or sensor 1 [%] | Resistors Bank 1, Sensor 2 Ω | Condition Heater after cat. ON/ Heater after cat. OFF | |||
042 | Oxygen Sensor heater Bank 2 | Resistor Bank 2, sensor 1 Ω | Condition or duty cycle Heater before cat. ON/ Heater before cat. OFF or sensor 1 [%] | Resistors Bank 2, Sensor 2 Ω | Condition Heater after cat. ON/ Heater after cat. OFF | |||
043 | Oxygen sensor ageing after Catalytic Converter, linear oxygen sensor, short trip Bank 1 | RPM 1/min | Exhaust gas / cat. converter temperature °C | Oxygen sensor voltage V | Result Test ON/Test OFF/ B1-S2 OK/B1-S2 not OK or B3-S2 OK/B3-S2 not OK | |||
044 | Oxygen sensor ageing after Catalytic Converter, linear oxygen sensor, short trip Bank 2 | RPM 1/min | Exhaust gas / cat. converter temperature °C | Oxygen sensor voltage V | Result Test ON/Test OFF/ B2-S2 OK/B2-S2 not OK or B4-S2 OK/B4-S2 not OK | |||
045 | NOX memory Catalytic Converter Bank 1, short trip | Factor memory entry NOx | Result Test ON/Test OFF/ Sys. OK/Sys. not OK | Factor memory entry NOx | Result Test ON/Test OFF/ Sys. OK/Sys. not OK | |||
046 | Catalytic Converter conversion test Bank 1 or Bank 3, short trip | RPM 1/min | Cat. converter temperature °C | Measuring value cat. Converter conversion | Result Test ON/Test OFF/ Cat B1 OK/ Cat B1 not OK or Cat B3 OK/ Cat B3 not OK | |||
047 | Catalytic Converter conversion test Bank 2 or Bank 4, short trip | RPM 1/min | Cat. converter temperature °C | Measuring value cat. Converter conversion | Result Test ON/Test OFF/ Cat B2 OK/ Cat B2 not OK or Cat B4 OK/ Cat B4 not OK | |||
048 | Thermal Catalytic Converter diagnosis Bank 1, short trip | Operating system BDE - | Number of test steps - | Exothermal temperature increase °K | Result Test ON/Test OFF/ Sys. OK/Sys. not OK | |||
049 | Thermal Catalytic Converter diagnosis Bank 2, short trip | Operating system BDE - | Number of test steps - | Exothermal temperature increase °K | Result Test ON/Test OFF/ Sys. OK/Sys. not OK | |||
050 | RPM Increase / Systems without separation for rear window defroster /A/C readiness | RPM actual value 1/min | RPM specified value 1/min | Rear window defroster/ Request for A/C -- ON/ OFF | A/C compressor -- ON/ OFF/ decrease | |||
050 | RPM Increase / Systems with separation for rear window defroster /A/C readiness | RPM actual value 1/min | RPM specified value 1/min | Rear window defroster/ Request for A/C -- ON/ OFF | A/C compressor -- ON/ OFF/ decrease | |||
051 | RPM, shift initiations | RPM actual value 1/min | RPM specified value 1/min | Driving range (only for automatic transmission) 0-6 / (Idle, driving ranges 1-6) | Supply voltage V | |||
052 | RPM Increase Systems with separation for rear window defroster /A/C readiness | RPM actual value 1/min | RPM specified value 1/min | A/C readiness ON/OFF | Rear window defroster ON/OFF | |||
053 | RPM increase based on generator load | RPM (actual value) 1/min | RPM (specified value) 1/min | Voltage V | Generator load % | |||
054 | Closed throttle position switch | RPM 1/min | Operating conditions (LL, TL, VL, SA, BA) | Throttle valve angle (Potentiometer) % | Throttle valve angle (Potentiometer) % | |||
055 | Closed throttle position switch for E-Gas-systems | RPM 1/min | Operating conditions (LL, TL, VL, SA, BA) | Sensor 1 for accelerator pedal position % | Throttle valve angle (Potentiometer) % | |||
056 | Idle air control | RPM 1/min | Idle air control | Current learning value for idle air control | Operating conditions | |||
057 | Idle air control | RPM (actual value) 1/min | RPM (specified value) 1/min | Idle air control valve | Operating conditions | |||
058 | Idle air control, pressure signal A/C compressor | RPM (actual value) 1/min | RPM (specified value) 1/min | A/C compressor ON/OFF/decreasing | Duty cycle pressure receiver % | |||
059 | RPM 1/min | Load % | Engine bearing 1 right ON/OFF | Engine bearing 2 left ON/OFF | ||||
060 | ESB adaption Vehicles with ESB | Throttle valve angle (potentiometer) % | Throttle valve angle (potentiometer) % | Operating condition (Idle, partial load, full load, deceleration enrichment, acceleration enrichment) | Adaption condition (ADP runs/ADP OK/ ADP ERROR = in emergency mode | |||
060 | E-Gas adaption Vehicles with E-Gas | Throttle valve angle (potentiometer 1) % | Throttle valve angle (potentiometer 2) % | Electrically controlled throttle valve adaption status N | Operating condition ADP runs/ADP OK/ ERROR | |||
061 | ESB/E-Gas Systems without separation for rear window defroster /A/C readiness | RPM 1/min | Supply voltage Ubat V | Triggering throttle valve control % If possible | Operating condition Condition fulfilled = 1; Condition not fulfilled = 0 | |||
061 | ESB/E-Gas Systems with separation for rear window defroster /A/C readiness | RPM 1/min | Supply voltage Ubat V | Triggering throttle valve control % If possible | Operating condition Condition fulfilled = 1; Condition not fulfilled = 0 | |||
062 | E-Gas, potentiometer voltage relationship U/Uref | Angle sensor 1 for throttle valve drive (0->100%) | Angle sensor 2 for throttle valve drive (0->100%) | Sensor 1 accelerator pedal position (0->100%) | Sensor 2 accelerator pedal position (0->100%) | |||
063 | Kick-down adaption | Sensor 1 accelerator pedal position (0->100%) | Sensor 1 learned Kick-down point (0->100%) | Switch Kick-down | ||||
064 | Throttle valve potentiometer adaption values | Potentiometer 1 lower adaption V | Potentiometer 2 1 lower adaption V | Emergency air gap potentiometer 1 V | ||||
065 | ||||||||
066 | Cruise control switched free for 4 position operating lever | Vehicle speed actual [km/h] | Switch positions | Vehicle speed specified [km/h] in 1 km/h-steps (only displayed when cruise control function is freely switched) | ||||
066 | Cruise control switched free for 6 position operating lever | Vehicle speed actual [km/h] | Switch positions xxxxxxxx | Vehicle speed specified [km/h] in 1 km/h-steps (is only issued with freely switched cruise control function) | Switch positions For 6 position operating lever | |||
067 | ||||||||
068 | ||||||||
069 | ||||||||
070 | Fuel tank venting and valve testing, short trip | Opening degree fuel tank ventilation Duty Cycle % | Lambda regular/ diagnostic value with active diagnose | Idle air control valve / diagnostic value with active diagnose % | Result Test ON/ Test OFF/ Fuel tank ventilation OK/ Fuel tank ventilation not OK. | |||
071 | Fuel tank leak test, short trip | Condition reed contact Reed Open / Reed Closed | DTC Small leak/large leak | Test status System test/measurement/ measurement end | Result Test ON/ Test OFF/ Abort Syst. OK/ Syst. Not OK | |||
072 | Tank leak test | |||||||
073 | ||||||||
074 | EGR regulator solenoid adaption | Null-Position V | Max. Stop V | Current potentiometer value V | Text Leak detection pump runs/ LDP OK/ ERROR | |||
075 | EGR, short trip Systems with Temp.-sensor | Engine RPM [1/min] | EGR-Temp. Sensor °C | EGR temperature difference °C | Result Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | |||
075 | EGR, short trip Systems with intake manifold pressure sensor | Engine RPM [1/min] | Intake manifold pressure [mbar] | Intake manifold pressure difference [mbar] | Result Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | |||
075 | EGR, for map adaption short trip Systems with intake manifold pressure sensor | Pressure difference diagnostics EGR phase 1 and 2 [hPa] | Pressure difference diagnostics EGR phase 2 and 3 [hPa] | Pressure difference diagnostics EGR phase 1 and 3 [hPa] | Result Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | |||
076 | EGR for pressure systems | Engine RPM [1/min] | Intake manifold pressure [mbar] | Opening degree (U/Uref) EGR potentiometer % | Duty cycle EGR valve % | |||
076 | EGR for air mass system | Engine RPM [1/min] | Last % | Opening degree (U/Uref) EGR potentiometer % | Duty cycle EGR valve % | |||
076 | EGR map adaption | Actual EGR value – potentiometer without offset V | Correction factor in the upper opening range % | Correction factor in the lower opening range % | Status Test OFF / Leak detection pump runs/ LDP OK/ ERROR | |||
077 | Test secondary air injection system, short trip, Bank 1 Systems with conventional oxygen sensor | RPM 1/min | Engine air mass g/sec | Air mass secondary air injection system g/sec | Result Test ON/ Test OFF/ Abort-- Syst. OK/ Syst. Not OK | |||
077 | Test secondary air injection system, short trip, Bank 1 Systems with linear oxygen sensor | RPM 1/min | Engine air mass g/sec | relative Air mass | Result Test ON/ Test OFF/ Abort-- Syst. OK/ Syst. Not OK | |||
078 | Test secondary air injection system, short trip Bank 2 Systems with conventional oxygen sensor | RPM 1/min | Engine air mass g/sec | Air mass secondary air injection system g/sec | Result Test ON/ Test OFF/ Abort-- Syst. OK/ Syst. Not OK | |||
078 | Test secondary air injection system, short trip, Bank 2 Systems with linear oxygen sensor | RPM 1/min | Engine air mass g/sec | relative Air mass | Result Test ON/ Test OFF/ Abort-- Syst. OK/ Syst. Not OK | |||
079 | ||||||||
080 | Control module identification (display shown at NA-No. 63) | Manufacturer’s code and marking | Manufacturing date | Manufacture’s change status | Manufacturer’s test stand number. | |||
081 | Control module identification (display shown at NA-No. 63) | Vehicle identification number | Limit No or serial number | Type test number | ||||
082 | Control module identification (display shown at NA-No. 63) | Flash tool code | Flash date | Hardware | Software | |||
083 | Control module identification | |||||||
084 | Control module identification | |||||||
085 | Control module identification | |||||||
090 | Camshaft adjustment Intake | RPM 1/min | Adjustment ON/OFF | Adjustment Bank 1 [°KW] | Adjustment Bank 2 [°KW] | |||
090 | Camshaft adjustment Exhaust | RPM 1/min | Adjustment ON/OFF | Adjustment Bank 1 [°KW] | Adjustment Bank 2 [°KW] | |||
090 | Continuous camshaft adjustment Exhaust Bank 1 | RPM 1/min | Duty cycle % | Adjustment specified [°KW] | Adjustment actual [°KW] | |||
091 | Camshaft adjustment Intake Bank 1 | RPM 1/min | Last % | Adjustment ON/OFF | Adjustment actual [°KW] | |||
091 | Continuous camshaft adjustment, Intake Bank 1 | RPM 1/min | Duty cycle % | Adjustment specified [°KW] | Adjustment actual [°KW] | |||
092 | Camshaft adjustment Intake Bank 2 | RPM 1/min | Last % | Adjustment ON/OFF | Adjustment actual [°KW] | |||
092 | Continuous camshaft adjustment, Intake Bank 2 | RPM 1/min | Duty cycle % | Adjustment specified [°KW] | Adjustment actual [°KW] | |||
093 | Camshaft adaption values Intake Bank 2 | RPM 1/min | Last % | Phase position [Deviation from correct position (shift of camshaft position sensor on shaft), 0 = Position OK] Bank 1[The phase position is displayed only when the phase adaptation was successfully concluded] [°KW] | Phase position Bank 2 [°KW] | |||
093 | Continuous camshaft adaption values | Phase position intake Bank 1 [°KW] | Phase position intake Bank 2 [°KW] | Phase position exhaust Bank 1 [°KW] | Phase position exhaust Bank 2 [°KW] | |||
094 | Camshaft adjustment Banks 1 and 2 Intake, short trip | RPM 1/min | Camshaft adjustment Text: Camshaft position ON / Camshaft position OFF | Test result Bank 1 Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | Test result Bank 2 Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | |||
094 | Continuous camshaft adjustment Banks 1 and 2 intake, short trip | RPM 1/min | Phase position intake [°KW] | Test result Bank 1 Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | Test result Bank 2 Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | |||
095 | Intake manifold change-over /Single step change-over | Engine RPM [1/min] | Last % | Coolant Temperature °C | Status ein/aus | |||
095 | Intake manifold change-over /Multi-step change-over | Engine RPM [1/min] | Last % | Coolant Temperature °C | Status Off /step 1/step 2 | |||
096 | Camshaft adjustment Banks 1 and 2 Exhaust, short trip | Engine RPM [1/min] | Camshaft adjustment Text: Camshaft position ON / Camshaft position OFF | Test result Bank 1 Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | Test result Bank 2 Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | |||
096 | Continuous camshaft adjustment Banks 1 and 2 Exhaust, short trip | RPM 1/min | Phase position exhaust [°KW] | Test result Bank 1 Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | Test result Bank 2 Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | |||
097 | Intake air change-over / Snow flap | RPM 1/min | Last % | Temperature / Pressure [°C]/[mbar] | Intake air change-over ON/ OFF | |||
098 | Continuous camshaft adjustment Exhaust Bank 2 | RPM 1/min | Duty cycle % | Adjustment specified [°KW] | Adjustment actual [°KW] | |||
099 | Shut-off l-Regulation (via basic setting) (for compatibility reasons with older systems) | RPM 1/min | Coolant Temperature °C | Lambda regulation [%] | Lambda regulation ON/OFF | |||
100 | eadiness code (for compatibility reasons with older systems) | Ready bits / 1= not concluded -- 0= concluded | Coolant temperature | Time since engine start | OBD-Status | |||
101 | Fuel injection Systems with Air mass measurement | RPM 1/min | Last % | Mean injection time (at deceleration = 0) ms | Air mass g/s | |||
101 | Fuel injection Systems with intake manifold pressure measurement | RPM 1/min | Last % | Mean injection time (at deceleration = 0) ms | Intake manifold pressure mbar | |||
102 | Fuel injection | RPM 1/min | Coolant Temperature °C | Intake air temperature °C | Mean injection time ms | |||
103 | Air-shrouded fuel injectors, short trip | RPM 1/min | Air mass idle air control [g/s] | LFR-Offset adaptation N | Result Test ON/Test OFF/ l injector OK /l injector not OK | |||
104 | Start adaptation values | Start engine temperature [°C] | Temperature adaptation factor 1 [%] | Temperature adaptation factor 2 [%] | Temperature adaptation factor 3 [%] | |||
105 | Cylinder shut off | RPM 1/min | Last % | Coolant Temperature °C | Shut-off (ON = Cylinder shut-off active; OFF = Cylinder shut-off not active) | |||
106 | ||||||||
107 | Lambda regulation, short trip | RPM 1/min | Lambda regulation Bank 1 (average value) [%] | Lambda regulation Bank 1 (average value) [%] | Result Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | |||
108 | ||||||||
109 | ||||||||
110 | Load, full load enrichment | RPM 1/min | Coolant Temperature °C | Average injection time ms | Throttle valve angle (Potentiometer) % | |||
111 | Boost pressure control | Adaption value boost pressure control RPM range 1 [%] | Adaption value boost pressure control RPM range 2 [%] | Adaption value boost pressure control RPM range 3 [%] | Adaption value boost pressure control RPM range 4 [%] | |||
112 | Exhaust gas temperature | Exhaust gas temperature Bank 1 [°C] | Enrichment factor sensor Bank 1 [%] | Exhaust gas temperature Bank 2 [%] | Enrichment factor sensor Bank 2 [%] | |||
113 | Last | RPM 1/min | Last % | Throttle valve angle (Potentiometer) % | Air pressure Mbar | |||
114 | Boost pressure control | Specified load without correction [%] | Specified load after correction [%] | Actual load [%] | Duty cycle Boost pressure valve [%] | |||
115 | Boost pressure control | RPM 1/min | Last % | Boost pressure specified value [mbar] | Boost pressure actual value [mbar] | |||
116 | Boost pressure control | RPM 1/min | Correction factor fuel [%] | Correction factor coolant temperature [%] | Correction factor intake air temperature [%] | |||
117 | Boost pressure control | RPM 1/min | Gas pedal position [%] | Throttle valve angle [%] | Boost pressure specified [mbar] | |||
118 | Boost pressure control | RPM 1/min | Intake air temperature °C | Duty cycle boost pressure control valve [%] | Boost pressure before throttle valve [mbar] | |||
119 | Boost pressure control | RPM 1/min | Actual adaption value boost pressure control valve [%] | Duty cycle boost pressure control valve [%] | Boost pressure before throttle valve [mbar] | |||
120 | ASR/FDR | RPM 1/min | Specified moment ASR/FDR [Nm] | Engine moment [Nm] | Status (ASR active/ASR not active) | |||
121 | ||||||||
122 | Transmission | RPM 1/min | Specified moment ASR/FDR [Nm] | Engine moment [Nm] | (Engine intervention /no intervention) | |||
123 | Reserved for CAN Bus signals | |||||||
124 | Reserved for CAN Bus signals | |||||||
125 | CAN Bus signals / see CAN-Product Description Manual | Transmission This corresponds with the desired sequence. Should there be no participant available a gap will remain at this place. | ABS32 | Instrument cluster32 | A/C32 | |||
126 | CAN Bus signals | ADR 32 | LWS 32 | Airbag32 | Electrical wiring32 | |||
127 | CAN Bus signals | All wheel32 | Level | Steering wheel | ||||
128 | CAN Bus signals | |||||||
129 | CAN Bus signals | |||||||
130 | Map cooling (coolant filling), Short trip | Temperature Engine outlet [°C] | Temperature Radiator outlet [°C] | Duty cycle Thermostat [%] | Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | |||
131 | Map cooling | Temperature Engine outlet [°C] | Temperature Engine outlet (specified) [°C] | Temperature Radiator outlet [°C] | Duty cycle Thermostat [%] | |||
132 | Map cooling | Temperature Radiator outlet [°C] | Temperature difference Engine and radiator outlet °C | Heater pre-run potentiometer % | Status cooling | |||
133 | ||||||||
134 | Temperature | Oil temperature [°C] | Ambient temperature [°C] | Intake air temperature [°C] | Engine outlet temperature [°C] | |||
135 | Coolant fan control, short trip | Temperature Radiator outlet (specified) [°C] | Duty cycle Coolant fan actuation 1 [%] | Duty cycle Coolant fan actuation 2 [%] | Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | |||
136 | Relay for coolant fan actuation | Relay 1 ON / OFF | Relay 2 ON / OFF | Relay 3 ON / OFF | Relay 4 ON / OFF | |||
137 | A/C requirements | AC-inlet ON / OFF | Compressor ON / OFF | High pressure switch or Pressure of A/C system ON / OFF or [bar] | Fan request from A/C system [%] | |||
140 | Pressure control valve, short trip | Duty cycle DSV [%] | Rail pressure specified [bar] | Rail pressure actual [bar] | Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | |||
141 | Fuel supply system | Rail pressure regulator [bar] | Regulator rail pressure system | Regulator rail pressure system residual portion | Status rail pressure system | |||
142 | ||||||||
143 | ||||||||
144 | ||||||||
145 | Exhaust gas temperature sensor, short trip | Exhaust gas temperature from model Bank 1 [°C] | Exhaust gas temperature sensor measured Bank 1 [°C] | Exhaust gas temperature sensor measured Bank 2 [°C] | Test ON/ Test OFF/ Syst. OK/ Syst. Not OK | |||
146 | ||||||||
147 | Charge movement flap for BDE | Charge movement flap Actual position [%] | Charge movement flap Specified position [%] | Offset value of potentiometer voltage LBK (V) | Adaptation condition ADP runs/ ADP OK/ Error (in emergency running mode) | |||
160 | Individual cylinder recognition/ Individual cylinder control | Normal Lambda control starting point cylinder 1 | Normal Lambda control starting point cylinder 2 | Normal Lambda control starting point cylinder 3 | Normal Lambda control starting point cylinder 4 | |||
161 | Individual cylinder recognition/ Individual cylinder control | Normal Lambda control starting point cylinder 5 | Normal Lambda control starting point cylinder 6 | Normal Lambda control starting point cylinder 7 | Normal Lambda control starting point cylinder 8 |
Habláremos del sistema de seguridad integrado en la marca BMW EWS1 El primer inmovilizador electrónico…
Los inyectores de Inyección Directa de Gasolina GDI (Gasoline Direct Injection) trabajan hasta 2,900 libras…
La tecnología start-stop detecta cuando su automóvil se detiene y detiene el motor automáticamente, luego…
El combustible FlexFuel, es un combustible alternativo elaborado a partir de una combinación de gasolina…
Debido a las altas velocidades involucradas, todos los flujos fuera y dentro de los cilindros…
DoIP, o Diagnóstico sobre Protocolo de Internet, es un protocolo de comunicación que permite el…
Esta web usa cookies.